|
 
Accessories
Premium Test Leads
NZ$43.00*
  • 4mm stackable plug with retracting shroud, 2mm probe tip
  • 1.5m x 1.5mm silicon insulated cable
  • 25 Amp, 600V CAT III rating
NZ$35.00*
  • 4mm shrouded plugs
  • Right angled to straight
  • 1m x 1.5mm silicon insulated, 25 Amp, 1000V CAT III rating
NZ$11.00*
  • Easy grip with anti-slip guard
  • 19 x 2mm probe tip
  • 36 Amp, 1000V CAT III rating
NZ$11.00*
  • Safer when testing around bus bars
  • Very fine needle probe
  • 16 Amp, 1000V CAT III rating
NZ$16.00*
  • Better than crushing your test leads
  • Easy-positive connection,Grooved for 4.3 & 6.3 mm bolts
  • 36 Amp, 33VAC, 70VDC rating
NZ$20.00*
  • Very fine 0.7mm sprung tip
  • Non-slip removable tip shroud
  • 1 Amp, 600V CAT III rating
NZ$45.00*
  • Spring tension holds and pierces
  • Excellent for loom tests
  • 6 Amp, 30VAC, 60VDC rating
NZ$21.00*
  • Holds well - even on very small pins
  • Rotatable pincers minimise test lead pull
  • Tested to 8000V! 6 Amp, 1000V CAT III rating
NZ$32.00*
  • Wide opening jaws & very positive grab
  • Insulated jaw backs prevent accidental shorts
  • Tested to 8000V! 6 Amp, 1000V CAT III rating
NZ$19.00*
  • Large 20mm bite & good strong grip
  • 3 nose teeth hold small conductors too
  • 20 Amp, 1000V CAT III rating
NZ$43.00*
  • 4mm right angled shrouded plug, 2mm probe tip
  • 1.5m x 1.5mm silicon insulated cable
  • 25 Amp, 1000V CAT III, 600V CAT III rating
Oscilloscope Probes
NZ$127.00*
  • A good quality general purpose oscilloscope probe
  • 1:1/10:1 Switchable, 20/150MHz Bandwidth
  • 400/600Vpk. 1.8/2.3ns Rise Time
NZ$266.00*
  • Attenuation = 1:100, Bandwidth = 300MHz
  • Maximum Voltage = 1500Vp, Rise Time = 1.2ns
  • One of two high voltage probes in the range. Both have enhanced BNC insulation.
NZ$314.00*
  • Attenuation = 1:100, Bandwidth = 300MHz
  • Maximum Voltage = 2500Vp, Rise Time = 1.2ns
  • The second of two high voltage probes in the range. Both have enhanced BNC insulation
NZ$367.00*
  • Attenuation = 1:10, Bandwidth = 350 MHz
  • Maximum Voltage = 600V, Rise Time = 1ns
  • With a 350MHz bandwidth, the 4011 is suitable for all but the very fastest Pico oscilloscope range
NZ$856.00*
  • Attenuation = 1:10, Bandwidth = 500 MHz
  • Maximum Voltage = 200V, Rise Time = 0.7ns
  • This high stability 500MHz probe has a smaller probe and is much easier to use on high density PCBs.
NZ$264.00*
  • Attenuation = 1:1, Bandwidth = 950 MHz
  • Maximum Voltage = 50V AC; 200V DC
  • A demodulating probe, the 7012 output is a DC voltage equal to the peak to peak value of the measured waveform
Temperature Probes
NZ$118.00*
  • Sharp point allows easy penetration for taking internal temperatures
  • Response time < 3 seconds
  • K-Type thermocouple - Max temperature 250°C, 3.3 x 130mm
NZ$131.00*
  • Spring-loaded sensing tip provides positive surface pressure
  • Response time < 2 seconds
  • K-Type thermocouple - Max temperature 250°C, 6 x 130mm
NZ$141.00*
  • High temperature probe - Ideal for weld temperatures
  • Response time < 1 second
  • K-Type thermocouple - Max 1000°C, 12 x 130mm
NZ$187.00*
  • High temperature weld temperatures
  • Response time < 1 second
  • K-Type thermocouple - Max 1000°C, 12 x 130mm
NZ$73.00*
  • Ideal for HVACR pipe work
  • Response time < 2 seconds
  • K-Type thermocouple - Maximum probe temperature 100°C. For pipe diameters from 6 to 30mm.
NZ$122.00*
  • Ideal for stationary, hard or metallic surfaces, as small as 8mm
  • Response time < 0.5 seconds
  • K-Type thermocouple - Max 250°C, 8 x 130mm
NZ$136.00*
  • Designed specifically to slide easily between packets or boxes of produce
  • Response time < 3 seconds
  • K-Type thermocouple - Max 250°C, 4.5 x 130mm
NZ$104.00*
  • Wrap-around probe suitable for the temperature measurement of medium and large pipes in the HVACR & process industries
  • Pipes up to 150mm diameter
  • K-Type thermocouple - Max 100°C, 20 x 500mm
NZ$138.00*
  • Suitable for liquids and soft or semi-solid food, soft rubber & plastic
  • Response time < 2 seconds
  • K-Type thermocouple - Max 250°C, 1.8 x 130mm
NZ$171.00*
  • Heavy Duty probe with T-Bar handle
  • Response time < 10 seconds
  • K-Type thermocouple - Max 250°C, 4.5 x 130mm
NZ$128.00*
  • For denser materials, raw food products and harder rubber
  • Response time < 4 seconds
  • K-Type thermocouple - Max 250°C, 4 x 130mm
NZ$149.00*
  • Long heavy duty penetration probe with T-Bar handle
  • Reduced sensing tip diameter for response time < 10 seconds
  • K-Type thermocouple - Max 250°C, 6.35 x 300mm
NZ$139.00*
  • Mineral insulation affords probe flexibility & high temperature range
  • Response time < 2 seconds
  • K-Type thermocouple - Max 1100°C, 1.5 x 130mm
NZ$128.00*
  • Rounded tip allows insertion through self-sealing binder glands in fluid filled pipes, vessels and radiators
  • Response time < 3 seconds
  • K-Type thermocouple, -75 ~ 250°C, 3.0 x 130mm
NZ$113.00*
  • For HVACR, Viticulture air and Aged/Infant care hot water measurements
  • Fast respose time < 0.5 seconds
  • K-Type thermocouple, -75 ~ 250°C, 4.5 x 130mm
NZ$155.00*
  • Designed for use in busy fast food kitchens
  • Stainless steel foot ensures consistently correct 6mm insertion depth
  • K-Type thermocouple, -75 ~ 250°C, 4.5 x 130mm with 1.0 x 6.0mm tip
NZ$84.00*
  • Measure & monitor ferrous metal surface temperatures e.g. heat exchangers and radiators
  • Response time < 20 seconds
  • K-Type thermocouple, -20 ~ 150°C, 1m cable, 20mm diameter magnet
NZ$19.00*
  • Measure or monitor fridges, freezers, ovens, water, air & curing concrete
  • Response time < 0.5 seconds
  • K-Type thermocouple, -6 ~ 250C, 1m or custom lengths
TPK01 Bead Probe
TPK01 Bead Probe
NZ$24.00*
  • Fast bead probe with easy-grip cable tidy handle
  • Use with full length, or as wrapped stub air probe
  • K-Type thermocouple, -60 ~ 250°, 1m
Economy Test Leads
NZ$15.00*
  • Non-shrouded right angled plugs
  • Replacement leads for 260T Clamp Meter
  • 1m long
NZ$15.00*
  • Shrouded right angled plugs
  • Compatible with 4mm shrouded meter sockets
  • 1m long with safety sleeved tips
NZ$15.00*
  • Straight 4 mm plugs with retracting shrouds
  • Shrouded Alligator Clips screw on/off probe tips
  • 1m long with Insulated plug tips
NZ$39.00*
  • Short & long insulated tips plug into probe end
  • Shrouded alligator clips plug into probes, or directly into meter
  • Right angled shrouded plugs on probe & alligator clip leads
Screw-on Alligator Clips for TL1108 Test Leads
Screw-on Alligator Clips for TL1108 Test Leads
NZ$12.00*
  • Screw-on Alligator clips for TL1108 test leads
  • CATIII 1000V, CATIV 600 V, 10 Amp rating
  • 14mm jaw opening
TL1108 Test Lead Pair with Insulated Tip Covers
TL1108 Test Lead Pair with Insulated Tip Covers
NZ$15.00*
  • Shrouded right-angled 4mm plugs
  • Removable anti-short probe caps cover all but very tips
  • Threaded probe collars accommodate TL05 Alligator Clips
Current Clamp Adaptors
NZ$203.00*
  • 0 to 60 Amps DC & AC @ 40Hz to 20kHz
  • Use with your DMM on Volts range to measure with 10mA resolution
  • Easy push-button Zero Set. 4mm Banana connectors on convenient curly cord.
NZ$203.00*
  • 0 to 600 Amps DC & AC @ 50 to 400Hz
  • Good choice for measuring car and SUV starter motor currents
  • Adjustable Zero Set. 4mm Banana connectors on curly cord.
NZ$89.00*
  • 0 to 1000 Amp AC @ 50 to 400Hz
  • Safely measure high currents with 1mV/A output
  • Wide mouthed 75 x 57mm jaw gets around large buss bars
TA167 - 200A/2000A AC/DC current clamp
TA167 - 200A/2000A AC/DC current clamp
NZ$482.00*
  • Measure high compression diesel and petrol starter currents
  • 0 to 200/2000 Amps DC & AC pk (to 20kHz)
  • Easy push-button Zero Set
Automotive Accessories
NZ$1213.00*
  • Perform quick and accurate pressure analysis of many automotive systems.
  • Accurately measure up to 34.47 Bar (500 psi). Auto zeroing. Ultra fast 100μs response time.
  • Internal rechargeable LiPo battery.
TA014 FirstLook Engine Diagnostic Sensor
TA014 FirstLook Engine Diagnostic Sensor
NZ$777.00*
  • Fast & accurate automotive diagnosis from tail pipe
  • Diagnose burnt valves, bad injectors & other problems without major disassembly
  • Includes vacuum line adaptor & connector cable
NZ$460.00*
  • Instantly Check Power & Ground Circuits
  • Identify Communication Link Protocols
  • Connect to PicoScope
6-Way Universal Breakout Lead
NZ$196.00*
  • Connect into any vehicle without specialised leads
  • Eliminates the need to own many specific breakout leads for engine diagnostics
  • Available with 0.6, 1.5, 2.3 & 2.8mm male & female spade connectors
TA012 Two Pin Break Out Lead
TA012 Two Pin Break Out Lead
NZ$49.00*
  • Enables voltage readings from numerous 2 pin sensors in the engine compartment
  • Separate access to individual wires allows easy current measurement with clamps
  • Simultaneously display both injector current and voltage on your PicoScope
Fuse Extension Lead
NZ$53.00*
  • ATC /ATO fuse extender keeps fuse in circuit while testing
  • Allows easy current (clamp) measurement.
  • Simply move fuse to extension, plug extension in where fuse was and clamp to measure
Mixmaster Secondary Ignition Pickups
Mixmaster Secondary Ignition Pickups
NZ$154.00*
  • A set of 4 secondary ignition, leads, each 40cm long
  • Combine with Mixmaster & 4-channel scope leads to display 12 channel parade
  • Get the most from your Mixmaster
Coil-on-Plug Extension Lead
NZ$64.00*
  • Single extension lead
  • Clip Pico secondary ignition lead over extension to see HT waveform
  • Simply fit between coil pack & plugs
Coil-On-Plug (COP) Ignition Probe & Cable
Coil-On-Plug (COP) Ignition Probe & Cable
NZ$350.00*
  • Display scope patterns of the secondary, faster than scoping the primary
  • Suitable for use on most COP & conventional ignition systems
  • Find misfires fast
Secondary Ignition Pickup
Secondary Ignition Pickup
NZ$93.00*
  • View secondary ignition waveforms directly on-screen with an Automotive Oscilloscope
  • Shielded 1.8m lead. Clips over plug lead or COP extension
  • For use with conventional ignition systems and most HEI and DIS systems
TA167 - 200A/2000A AC/DC current clamp
TA167 - 200A/2000A AC/DC current clamp
NZ$482.00*
  • Measure high compression diesel and petrol starter currents
  • 0 to 200/2000 Amps DC & AC pk (to 20kHz)
  • Easy push-button Zero Set
Mixmaster 12 Cylinder Auto Signal Mixer
Mixmaster 12 Cylinder Auto Signal Mixer
NZ$689.00*
  • View ignition parades of up to 12 cylinders
  • Display 2 engine banks of up to 6 cylinders each
  • Supplied with 4 secondary ignition leads, extra leads available
TA008 Acupuncture Back Pinning Probe Set
TA008 Acupuncture Back Pinning Probe Set
NZ$75.00*
  • Back pinning probe set
  • Fit onto 4mm banana plugs, fine tips slide easily past connector seals
  • 7 complete acupuncture probes, 3 probe sizes, replacement screws & needles
Multimeter Probe
NZ$11.00*
  • When a quick non-clip-on connection is required
  • Pushes easily onto a Pico Premium Test Lead
  • 4mm socket, length 115mm. Also available in black
Flexible Back Pinning Probe
NZ$7.00*
  • Designed for back-probing under the insulation
  • Flexible mid-section improves access to difficult terminals
  • Fits easily onto Pico Premium Test Leads
Large Dolphin/Gator Clip
NZ$16.00*
  • Fully insulated with a 4 mm socket in the handle
  • Easy connection to Pico Premium test lead
  • Wide 30 mm opening jaw
Small Crocodile / Gator Clip
NZ$5.00*
  • Fully insulated with 4mm socket in the handle
  • Toothed grip offers good contact on fine wire
  • Easy connection to Pico Premium Test Leads
Battery Clip
Battery Clip
NZ$5.00*
  • Red single
  • Fits all our BNC to 4 mm Pico Premium Test Leads
  • Plier type clips designed to grab and hold the vehicle battery terminals
Red/Black Pair of Insulation Piercing Clips
Red/Black Pair of Insulation Piercing Clips
NZ$93.00*
  • Provides the exact pressure needed to pierce the insulation of a wide range of wires
  • Rotating banana jacks prevent test lead twisting
  • Keeps the oscilloscope in-circuit while the wire is pierced
Shrouded to Unshrouded Adaptor
NZ$5.00*
  • Adapts 4mm shrouded plug to unshrouded plug
  • Allows test lead connection into any breakout box
  • Quick push-on connection
Premium Test Lead: BNC to 4 mm
NZ$276.00*
  • Set of four colours, removable and fixed ground
  • Leads match scope trace colours
  • 3m insulated BNC to stackable shrouded banana plugs
Premium test leads 5m long
NZ$460.00*
  • For working on larger vehicles
  • 5m long BNC to 4mm cable, with 2.5m fixed ground
  • Insulated BNC connector, shrouded 4mm plugs
TA197 10:1 Attenuator
TA197 10:1 Attenuator
NZ$102.00*
  • Perform quick and accurate ignition waveform analysis of many automotive systems
  • Allows voltages of up to 400 V to be measured
  • Increases the input impedance of the oscilloscope from 1 MΩ to 8 MΩ
USB Cable
NZ$22.00*
  • Connect PicoScope to PC
  • Scope power and high signal rating
  • Compatible with USB2 PCs
Keyless entry carrier signal detector
Keyless entry carrier signal detector
NZ$44.00*
  • Detect the presence of the keyless entry carrier frequency
  • In the range of 125-140 kHz
  • 3m long lead
Ultrasonic parking sensor detector
Ultrasonic parking sensor detector
NZ$44.00*
  • Prove the correct operation of each of the ultrasonic parking sensors
  • Directly showing the strength of the signal from a given sensor
  • 2m long lead
MI168 S-Hook
MI168 S-Hook
NZ$5.00*
  • Makes it easy to keep test leads tidy in the engine bay
  • Hang PicoScope up by its boot loop
  • 100 mm long, plastic coated with rubber caps
Auto-Solve Diagnostic Assistance Software
Auto-Solve Diagnostic Assistance Software
NZ$535.00*
  • Suitable for all mechanics, diagnostics technicians & apprentices
  • 360 topics and 170 comparative waveforms help make quick & accurate diagnosis
  • Guided component testing on 66 different automotive sensors and actuators
NZ$40.00*
  • For use with the Coil-On-Plug Ignition Probe
  • Length: 3 metres
Tachometers
NZ$6.00*
  • Use for all of our 2200 Series non-contact tachometer measurements
  • 600mm and highly reflective
  • Peel-off backing, self-adhesive
NZ$5.00*
  • Fits DT2230 tachometer
  • Replacement tip for end-on shaft tachometer measurements
NZ$5.00*
  • Fits DT2230 tachometer
  • Replacement tip for rounded-end shaft tachometer measurements
*15% GST applicable for sales within NZ