subcategories
*15% GST applicable for sales within NZ
TA300 current probe 40 A AC/DC D9 connector
- 40 A AC/DC, 300 V CAT III
- 100 kHz current measurement
- Used with the PicoScope 4444 only
TA325 Flex current probe 3-phase 30/300/3000 A AC BNC
- Flexible 3-phase switched-range 30/300/3000 A AC RMS
- 1000 V CAT III, 10 Hz to 20 kHz current probe
- Used with the PicoScope 4444 only
- 3 x TA271 D9-BNC Adaptors required
PicoConnect 441 differential 1:1 probe
- General-purpose passive differential probe
- Measuring voltages on ranges from ±10 mV to ±50 V
- Used with the PicoScope 4444 only
TA301 current probe 200/2000 A AC/DC D9 connector
- 200/2000 A AC/DC, 150 V CAT II
- 20 kHz current measurement probe
- Used with the PicoScope 4444 only
TA326 Flex current probe 30/300/3000 A AC BNC
- Flexible single-phase switched-range 30/300/3000 A AC RMS
- 1000 V CAT III, 10 Hz to 20 kHz current probe
- Used with the PicoScope 4444 only
M5001 Oscilloscope Probe
- Attenuation = 1:10, Bandwidth = 500 MHz
- Maximum Voltage = 200V, Rise Time = 0.7ns
- This high stability 500MHz probe has a smaller probe and is much easier to use on high density PCBs.
D9-BNC adaptor
- Suitable for ground-referenced measurements
- Essential when using the TA325 and TA326 current probes
- Used with the PicoScope 4444 only
DR7012 Oscilloscope Probe
- Attenuation = 1:1, Bandwidth = 950 MHz
- Maximum Voltage = 50V AC; 200V DC
- A demodulating probe, the 7012 output is a DC voltage equal to the peak to peak value of the measured waveform
PicoConnect 442 1000 V CAT III 25:1 differential probe
- 1000 V CAT III, passive differential probe
- 25:1 10 MHz voltage measurement
- Used with the PicoScope 4444 only
D9-dual BNC adaptor
- Suitable for differential measurements using two single-ended probes
- Used with the PicoScope 4444 only
PicoScope 4444 carry case
- Hold the PicoConnect 4444 and its accessories
- Portable
PicoConnect RF, microwave and pulse passive probe
- Up to 5 GHz bandwidth
- Fits all SMA, K and PC3.5 50 Ω input ports
- Less than 70 ps transition time
PicoConnect gigabit passive probe
- High-speed logic voltage applications
- Less than 40 ps transition time
- Suited to Ethernet, USB3, HDMI, SATA, PCI, LVD and other high-speed cabled, chip to chip and backplane interfaces
PicoScope 6000E Series MSO pod, 8 channels
- 8 digital inputs per pod
- 500 MHz bandwidth, 1 Gb/s
- 5 GS/s sampling on 16 digital channels
A3136 1.3 GHz active oscilloscope probe
- High input impedance up to 1.3 GHz
- input resistance of 1 MΩ
- capacitance of 0.9 pF
S1021 Oscilloscope Probe
- A good quality general purpose oscilloscope probe
- 1:1/10:1 Switchable, 20/150MHz Bandwidth
- 400/600Vpk. 1.8/2.3ns Rise Time
V6021 Oscilloscope Probe
- Attenuation = 1:100, Bandwidth = 300MHz
- Maximum Voltage = 1500Vp, Rise Time = 1.2ns
- One of two high voltage probes in the range. Both have enhanced BNC insulation.
V6041 Oscilloscope Probe
- Attenuation = 1:100, Bandwidth = 300MHz
- Maximum Voltage = 2500Vp, Rise Time = 1.2ns
- The second of two high voltage probes in the range. Both have enhanced BNC insulation
H4011 Oscilloscope Probe
- Attenuation = 1:10, Bandwidth = 350 MHz
- Maximum Voltage = 600V, Rise Time = 1ns
- With a 350MHz bandwidth, the 4011 is suitable for all but the very fastest Pico oscilloscope range
A3076 750 MHz active oscilloscope probe
- High input impedance up to 750 MHz
- Input resistance of 1 MΩ
- Capacitance of 0.9 pF
P2056 passive oscilloscope probe: 500 MHz
- 500 MHz Bandwidth
P2036 passive oscilloscope probe: 300 MHz
- 300 MHz Bandwidth