subcategories
*15% GST applicable for sales within NZ
Fuse Extension Lead
- ATC /ATO fuse extender keeps fuse in circuit while testing
- Allows easy current (clamp) measurement.
- Simply move fuse to extension, plug extension in where fuse was and clamp to measure
4213 Premium Test Lead Pair
- 4mm stackable plug with retracting shroud, 2mm probe tip
- 1.5m x 1.5mm silicon insulated cable
- 25 Amp, 600V CAT III rating
CA60 AC/DC Current Clamp Adaptor
- 0 to 60 Amps DC & AC @ 40Hz to 20kHz
- Use with your DMM on Volts range to measure with 10mA resolution
- Easy push-button Zero Set. 4mm Banana connectors on convenient curly cord.
WPS500X Automotive Pressure Transducer
- Perform quick and accurate pressure analysis of many automotive systems.
- Accurately measure up to 34.47 Bar (500 psi). Auto zeroing. Ultra fast 100μs response time.
- Internal rechargeable LiPo battery.
S1021 Oscilloscope Probe
- A good quality general purpose oscilloscope probe
- 1:1/10:1 Switchable, 20/150MHz Bandwidth
- 400/600Vpk. 1.8/2.3ns Rise Time
HHK160 Penetration Probe
- Sharp point allows easy penetration for taking internal temperatures
- Response time < 3 seconds
- K-Type thermocouple - Max temperature 250°C, 3.3 x 130mm
PE03 General Purpose pH Electrode
- Wide epoxy body for strength
- General lab use, economic electrode
- 12.3 x 160mm
2353 100 Red/Black Patchcord Pair
- 4mm shrouded plugs
- Right angled to straight
- 1m x 1.5mm silicon insulated, 25 Amp, 1000V CAT III rating
TS10 Shrouded Test Lead Pair
- Shrouded right angled plugs
- Compatible with 4mm shrouded meter sockets
- 1m long with safety sleeved tips
V6021 Oscilloscope Probe
- Attenuation = 1:100, Bandwidth = 300MHz
- Maximum Voltage = 1500Vp, Rise Time = 1.2ns
- One of two high voltage probes in the range. Both have enhanced BNC insulation.
HHK000 Surface Probe
- Spring-loaded sensing tip provides positive surface pressure
- Response time < 2 seconds
- K-Type thermocouple - Max temperature 250°C, 6 x 130mm
2236RT Reflective Tape
- Use with all of our 2200 Series non-contact tachometers
- 600mm and highly reflective
- Peel-off backing, self-adhesive
405 Test Probe
- Easy grip with anti-slip guard
- 19 x 2mm probe tip
- 36 Amp, 1000V CAT III rating
CA600 AC/DC Current Clamp Adaptor
- 0 to 600 Amps DC & AC @ 50 to 400Hz
- Good choice for measuring car and SUV starter motor currents
- Adjustable Zero Set. 4mm Banana connectors on curly cord.
V6041 Oscilloscope Probe
- Attenuation = 1:100, Bandwidth = 300MHz
- Maximum Voltage = 2500Vp, Rise Time = 1.2ns
- The second of two high voltage probes in the range. Both have enhanced BNC insulation
HHK020 Heavy Duty Surface Probe
- High temperature probe - Ideal for weld temperatures
- Response time < 1 second
- K-Type thermocouple - Max 1000°C, 12 x 130mm
2230CT Cone Tip
- Fits DT2230 tachometer
- Replacement tip for end-on shaft tachometer measurements
PE06HD Spear Tipped pH Electrode
- Spear tipped for penetration measurement in cheese, meats, soil
- Perfect (easy-clean) for sushi
- 12 x 160mm with fine spear-shaped tip
TL8000 Interchangeable Test Lead Set
- Short & long insulated tips plug into probe end
- Shrouded alligator clips plug into probes, or directly into meter
- Right angled shrouded plugs on probe & alligator clip leads
H4011 Oscilloscope Probe
- Attenuation = 1:10, Bandwidth = 350 MHz
- Maximum Voltage = 600V, Rise Time = 1ns
- With a 350MHz bandwidth, the 4011 is suitable for all but the very fastest Pico oscilloscope range
HHK028 Right Angled Surface Probe
- High temperature weld temperatures
- Response time < 1 second
- K-Type thermocouple - Max 1000°C, 12 x 130mm
2230FT Funnel Tip
- Fits DT2230 tachometer
- Replacement tip for rounded-end shaft tachometer measurements
Soft Padded Case for CA40
- Soft anti-scratch liner
- Internally padded. Velcro secured flap
- 240(L) x 90(W) x 34mm
PE12 Electrode Head
- Replacement electrode & thermistor head for PH222 pH Meter
- Quick and easy swap-over
- Positive push-on, with screw-ring retainer
CA1000 AC Clamp Adaptor
- 0 to 1000 Amp AC @ 50 to 400Hz
- Safely measure high currents with 1mV/A output
- Wide mouthed 75 x 57mm jaw gets around large buss bars
pH Buffer Capsules
- 10 x pH4 Buffer Capsules
- Easy pH meter calibration
- Simply mix into 100ml of distilled water
M5001 Oscilloscope Probe
- Attenuation = 1:10, Bandwidth = 500 MHz
- Maximum Voltage = 200V, Rise Time = 0.7ns
- This high stability 500MHz probe has a smaller probe and is much easier to use on high density PCBs.
HHK040 Pipe Clamp Probe
- Ideal for HVACR pipe work
- Response time < 2 seconds
- K-Type thermocouple - Maximum probe temperature 100°C. For pipe diameters from 6 to 30mm.
Soft Clampmeter Carry Case
- Soft anti-scratch liner with internal pocket for test leads
- Secure zip fastener & external carry tab
- 330(L) x 140(W) x 50mm - For 2600 & 3600 series clamps
DR7012 Oscilloscope Probe
- Attenuation = 1:1, Bandwidth = 950 MHz
- Maximum Voltage = 50V AC; 200V DC
- A demodulating probe, the 7012 output is a DC voltage equal to the peak to peak value of the measured waveform
HHK044 Ribbon Surface Probe
- Ideal for stationary, hard or metallic surfaces, as small as 8mm
- Response time < 0.5 seconds
- K-Type thermocouple - Max 250°C, 8 x 130mm
TA167 - 200A/2000A AC/DC current clamp
- Measure high compression diesel and petrol starter currents
- 0 to 200/2000 Amps DC & AC pk (to 20kHz)
- Easy push-button Zero Set
Insulation Test Lead for 3604
- Insulation test probe for 3604
- In-probe button activates insulation test
- Use in conjunction with the red test lead and clip
HHK060 Rigid Between Pack Probe
- Designed specifically to slide easily between packets or boxes of produce
- Response time < 3 seconds
- K-Type thermocouple - Max 250°C, 4.5 x 130mm
HHK080 Velcro Pipe Probe
- Wrap-around probe suitable for the temperature measurement of medium and large pipes in the HVACR & process industries
- Pipes up to 150mm diameter
- K-Type thermocouple - Max 100°C, 20 x 500mm
TP07 Temperature Probe for PH207
- Use with PH207 pH meter for automatic temperature compensation
- Also compatible with PH208, PH209YK, PH221 and WA2000 Series
- 110 x 4mm (+handle), 0~60°
402 Long Insulated Probe
- Safer when testing around bus bars
- Very fine needle probe black
- 16 Amp, 1000V CAT III rating
Coil-On-Plug (COP) Ignition Probe & Cable
- Display scope patterns of the secondary, faster than scoping the primary
- Suitable for use on most COP & conventional ignition systems
- Find misfires fast
Needle Penetration Probe
- Suitable for liquids and soft or semi-solid food, soft rubber & plastic
- Response time < 2 seconds
- K-Type thermocouple - Max 250°C, 1.8 x 130mm
Mixmaster 12 Cylinder Auto Signal Mixer
- View ignition parades of up to 12 cylinders
- Display 2 engine banks of up to 6 cylinders each
- Supplied with 4 secondary ignition leads, extra leads available
HHK116 Heavy Duty Chisel Point Probe
- Heavy Duty probe with T-Bar handle
- Response time < 10 seconds
- K-Type thermocouple - Max 250°C, 4.5 x 130mm
BNC to BNC Cable with Earth Clamp
- For use with the Coil-On-Plug Ignition Probe
- Length: 3 metres
Mixmaster Secondary Ignition Pickups
- A set of 4 secondary ignition, leads, each 40cm long
- Combine with Mixmaster & 4-channel scope leads to display 12 channel parade
- Get the most from your Mixmaster
HHK117 Heavy Duty Penetration Probe
- For denser materials, raw food products and harder rubber
- Response time < 4 seconds
- K-Type thermocouple - Max 250°C, 4 x 130mm
HHK120 Asphalt Probe
- Long heavy duty penetration probe with T-Bar handle
- Reduced sensing tip diameter for response time < 10 seconds
- K-Type thermocouple - Max 250°C, 6.35 x 300mm
Secondary Ignition Pickup
- View secondary ignition waveforms directly on-screen with an Automotive Oscilloscope
- Shielded 1.8m lead. Clips over plug lead or COP extension
- For use with conventional ignition systems and most HEI and DIS systems
High Temperature Mineral Insulated Probe
- Mineral insulation affords probe flexibility & high temperature range
- Response time < 2 seconds
- K-Type thermocouple - 1.5 x 130mm
3034 Spade Adaptor Pair
- Better than crushing your test leads
- Easy-positive connection,Grooved for 4.3 & 6.3 mm bolts
- 36 Amp, 33VAC, 70VDC rating
Coil-on-Plug Extension Lead
- Single extension lead
- Clip Pico secondary ignition lead over extension to see HT waveform
- Simply fit between coil pack & plugs
464 SMD Probe
- Very fine 0.7mm sprung tip
- Non-slip removable tip shroud
- 1 Amp, 600V CAT III rating
HHK240 Binder Probe
- Rounded tip allows insertion through self-sealing binder glands in fluid filled pipes, vessels and radiators
- Response time < 3 seconds
- K-Type thermocouple, -75 ~ 250°C, 3.0 x 130mm
HHK300 Air/Gas/Hot Water Probe
- For HVACR, Viticulture air and Aged/Infant care hot water measurements
- Fast respose time < 0.5 seconds
- K-Type thermocouple, -75 ~ 250°C, 4.5 x 130mm
HHK745 Burger Probe
- Designed for use in busy fast food kitchens
- Stainless steel foot ensures consistently correct 6mm insertion depth
- K-Type thermocouple, -75 ~ 250°C, 4.5 x 130mm with 1.0 x 6.0mm tip
Keyless entry carrier signal detector
- Detect the presence of the keyless entry carrier frequency
- In the range of 125-140 kHz
- 3m long lead
HHK016 Magnetic Probe
- Measure & monitor ferrous metal surface temperatures e.g. heat exchangers and radiators
- Response time < 20 seconds
- K-Type thermocouple, -20 ~ 150°C, 1m cable, 20mm diameter magnet
Ultrasonic parking sensor detector
- Prove the correct operation of each of the ultrasonic parking sensors
- Directly showing the strength of the signal from a given sensor
- 2m long lead
HHK362 Exposed Junction Bead Probe
- Measure or monitor fridges, freezers, ovens, water, air & curing concrete
- Response time < 0.5 seconds
- K-Type thermocouple, -60 ~ 250°C, 1m or custom lengths
- 1.5mm x 1000mm or talk to us about custom lengths
TPK01 Bead Probe
- Fast bead probe with easy-grip cable tidy handle
- Use with full length, or as wrapped stub air probe
- K-Type thermocouple, -60 ~ 250°, 1m
6003 Insulation Piercing Grabber
- Spring tension holds and pierces
- Excellent for loom tests
- 6 Amp, 30VAC, 60VDC rating
Premium test leads 5m long
- For working on larger vehicles
- 5m long black BNC to 4mm cable, with 2.5m fixed ground
- Insulated BNC connector, shrouded 4mm plugs
Premium Test Lead: BNC to 4 mm
- Fully shielded for the complete length of the signal cable
- Color coded BNCs for the scope connections
- 3m insulated BNC to stackable shrouded banana plugs
6005 Flexible Pincer Grabber
- Holds well - even on very small pins
- Rotatable pincers minimise test lead pull
- Tested to 8000V! 6 Amp, 1000V CAT III rating
MI168 S-Hook
- Makes it easy to keep test leads tidy in the engine bay
- Hang PicoScope up by its boot loop
- 100 mm long, plastic coated with rubber caps
6007 Long Alligator Grabber
- Wide opening jaws & very positive grab
- Insulated jaw backs prevent accidental shorts
- Tested to 8000V! 6 Amp, 1000V CAT III rating
5004 Large Crocodile Clip Pair
- Large 20mm bite & good strong grip
- 3 nose teeth hold small conductors too
- 20 Amp, 1000V CAT III rating
4413 Red/Black Test Lead Pair
- 4mm right angled shrouded plug, 2mm probe tip
- 1.5m x 1.5mm silicon insulated cable
- 25 Amp, 1000V CAT III, 600V CAT III rating
Large Dolphin/Gator Clip
- Fully insulated with a 4 mm socket in the handle
- Easy connection to Pico Premium test lead
- Wide 30 mm opening jaw
Small Crocodile / Gator Clip
- Fully insulated with 4mm socket in the handle
- Toothed grip offers good contact on fine wire
- Easy connection to Pico Premium Test Leads
Battery Clip
- Fits all our BNC to 4 mm Pico Premium Test Leads
- Plier type clips designed to grab and hold the vehicle battery terminals
Red/Black Pair of Insulation Piercing Clips
- Provides the exact pressure needed to pierce the insulation of a wide range of wires
- Rotating banana jacks prevent test lead twisting
- Keeps the oscilloscope in-circuit while the wire is pierced
TA008 Acupuncture Back Pinning Probe Set
- Back pinning probe set
- Fit onto 4mm banana plugs, fine tips slide easily past connector seals
- 7 complete acupuncture probes, 3 probe sizes, replacement screws & needles
Flexible Back Pinning Probe
- Designed for back-probing under the insulation
- Flexible mid-section improves access to difficult terminals
- Fits easily onto Pico Premium Test Leads
Multimeter Probe
- When a quick non-clip-on connection is required
- Pushes easily onto a Pico Premium Test Lead
- 4mm socket, length 115mm. Also available in black
Shrouded to Unshrouded Adaptor
- Adapts 4mm shrouded plug to unshrouded plug
- Allows test lead connection into any breakout box
- Quick push-on connection
6-Way Universal Breakout Lead
- Connect PicoScope any vehicle - Micro(0.6 mm)
- Eliminates the need to own many specific breakout leads for engine diagnostics
- Available with 0.6, 1.5, 2.3 & 2.8mm male & female spade connectors
TA012 Two Pin Break Out Lead
- Enables voltage readings from numerous 2 pin sensors in the engine compartment
- Separate access to individual wires allows easy current measurement with clamps
- Simultaneously display both injector current and voltage on your PicoScope
PP619 CAN-Bus Test Box
- Instantly Check Power & Ground Circuits
- Identify Communication Link Protocols
- Connect to PicoScope
TA014 FirstLook Engine Diagnostic Sensor
- Fast & accurate automotive diagnosis from tail pipe
- Diagnose burnt valves, bad injectors & other problems without major disassembly
- Includes vacuum line adaptor & connector cable
TA197 10:1 Attenuator
- Perform quick and accurate ignition waveform analysis of many automotive systems
- Allows voltages of up to 400 V to be measured
- Increases the input impedance of the oscilloscope from 1 MΩ to 8 MΩ
USB Cable
- Connect PicoScope to PC
- Scope power and high signal rating
- Compatible with USB2 PCs