subcategories
*15% GST applicable for sales within NZ
Fuse Extension Lead
- ATC /ATO fuse extender keeps fuse in circuit while testing
- Allows easy current (clamp) measurement.
- Simply move fuse to extension, plug extension in where fuse was and clamp to measure
WPS500X Automotive Pressure Transducer
- Perform quick and accurate pressure analysis of many automotive systems.
- Accurately measure up to 34.47 Bar (500 psi). Auto zeroing. Ultra fast 100μs response time.
- Internal rechargeable LiPo battery.
NVH Starter Diagnostic Kit
- Identify unwanted vibration and noise sources in a vehicle.
- Provides real-time diagnosis for the technician
- Three axis starter kit in foam tray
PicoScope 4225A
2 Channel Starter Kit
- Lowest possible cost entry into your PicoScope ownership
- Comes complete with a basic set of leads and clips
- Accessories can be added at any time, to upgrade the kit and broaden its applications base.
TA467 Automotive Tester
- For Vehicles With High On-Board Voltages
- Comprehensive Measurement Functions
- Data Storage and Wireless Connectivity
- Full Multimeter Functionality
- Durable, Waterproof Design
NVH Standard Diagnostic Kit
- Enables the identification of unwanted vibration and noise sources in a vehicle.
- Providing real-time simultaneous diagnosis for the technician
- Four axis kit in foam tray
PicoScope 4425A
4 Channel Starter Kit
- Contains the same 4 channel Scope featured in the Standard and Advanced kits
- Supplied with a set of leads and clips to perform the more common tasks
- Purchase accessories to upgrade to a standard or advanced kit.
PicoScope Automotive Oscilloscope
- Up to 400 MS/s real-time sample rate
- 20 MHz bandwidth
- Easy to use with any vehicle
Advanced NVH Diagnostic Kit
- Four Noise, Vibration and Harshness modules to use with...
- 4 channel PicoScopes for single or multi-axis analysis.
- Kit includes 4 triple-axis accelerometers, 4 microphones and extension cables
PicoScope 4225A
2 Channel Standard Kit
- Comes complete with a variety of accessories
- Test virtually all the components on modern vehicles
- Ideal for occasional use or for those on a limited budget
Optical sensor kit
- Providing a high-quality optical sensor and magnetic mount for use with our balancing software
- Primarily used for balancing of propshafts
- Also supports frequency measurement of other rotating items.
PicoScope 4425A
4 Channel Standard Kit
- Four input channels are a particular advantage when testing the likes of ABS systems
- Fast enough to keep up with the emerging FlexRay standard
- Supplied with a comprehensive array of connection and interfacing accessories
- Smart connectors
3-Axis NVH Interface
- Add more inputs to your PicoDiagnostics NVH kit
- Use with Picoscope TA143 MEMS Accelerometer or the TA144 Microphone
PicoScope 4425A
4 Channel Advanced Kit
- The Advanced Kit builds on the standard kit to include more accessories
- Includes universal break out leads, fuse extensions, COP probes and extension leads
- Oscilloscope buffer memory has 250 Meg samples
PicoBNC+ 60A AC/DC current clamp
- For measuring currents between 10 mA and 60 A
- Display current waveforms for fuel injectors and fuel pumps.
- Improved performance and diagnostic accuracy
TA167 - 200A/2000A AC/DC current clamp
- Measure high compression diesel and petrol starter currents
- 0 to 200/2000 Amps DC & AC pk (to 20kHz)
- Easy push-button Zero Set
NVH Starter to Standard Kit Upgrade
- Upgrade your starter kit
- Add an additional sound input and an extra 3-axis accelerometer
PicoScope 4425A
4 Channel Diesel Kit
- Specifically designed around heavy duty diesel engines
- Includes a 2000 Amp DC clamp
- Fast sampling rate supports the capture and viewing of FlexRay and CAN bus signals
PicoScope 4425A
4 Channel Master Kit
- The Master Kit has you covered with a raft of accessories
- Includes universal break out leads, fuse extensions, COP probes and extension leads
- Oscilloscope buffer memory has 250 Meg samples
PicoBNC+ 2000 A AC/DC current clamp
- Allows you to measure up to 2000 amps without cutting, or disconnecting or stripping wires
- No batteries required
- Ranging is carried out automatically with no user switching required
PicoBNC+ COP and signal probe
- Displays scope patterns of the secondary, faster than scoping the primary
- Flexible design allows for easier access to hard-to-reach components
- No batteries required
Coil-On-Plug (COP) Ignition Probe & Cable
- Display scope patterns of the secondary, faster than scoping the primary
- Suitable for use on most COP & conventional ignition systems
- Find misfires fast
Mixmaster 12 Cylinder Auto Signal Mixer
- View ignition parades of up to 12 cylinders
- Display 2 engine banks of up to 6 cylinders each
- Supplied with 4 secondary ignition leads, extra leads available
BNC to BNC Cable with Earth Clamp
- For use with the Coil-On-Plug Ignition Probe
- Length: 3 metres
Mixmaster Secondary Ignition Pickups
- A set of 4 secondary ignition, leads, each 40cm long
- Combine with Mixmaster & 4-channel scope leads to display 12 channel parade
- Get the most from your Mixmaster
Secondary Ignition Pickup
- View secondary ignition waveforms directly on-screen with an Automotive Oscilloscope
- Shielded 1.8m lead. Clips over plug lead or COP extension
- For use with conventional ignition systems and most HEI and DIS systems
PicoBNC+ secondary ignition pickup
- View secondary ignition waveforms directly on-screen with an Automotive Oscilloscope
- Shielded 1.8m lead. Clips over plug lead or COP extension
- This lead is fitted with a PicoBNC+ interface
Coil-on-Plug Extension Lead
- Single extension lead
- Clip Pico secondary ignition lead over extension to see HT waveform
- Simply fit between coil pack & plugs
PicoBNC+ Temperature probe (wide-range linear)
- Measures in the range -40° to 125°
- Enclosed in a 5mm stainless steel housing to provide contact and airflow measurement.
- Available only for PicoBNC+
Keyless entry carrier signal detector
- Detect the presence of the keyless entry carrier frequency
- In the range of 125-140 kHz
- 3m long lead
Ultrasonic parking sensor detector
- Prove the correct operation of each of the ultrasonic parking sensors
- Directly showing the strength of the signal from a given sensor
- 2m long lead
Premium test leads 5m long
- For working on larger vehicles
- 5m long black BNC to 4mm cable, with 2.5m fixed ground
- Insulated BNC connector, shrouded 4mm plugs
Premium Test Lead: BNC to 4 mm
- Fully shielded for the complete length of the signal cable
- Color coded BNCs for the scope connections
- 3m insulated BNC to stackable shrouded banana plugs
MI168 S-Hook
- Makes it easy to keep test leads tidy in the engine bay
- Hang PicoScope up by its boot loop
- 100 mm long, plastic coated with rubber caps
Insulated BNC to BNC cable - 0.5 m
- Insulated BNC to BNC cable, measuring 50 cm (0.5 m) in length.
PicoBNC+ Premium Test Lead to 4mm, 3m
- Fully shielded for the complete length of the signal cable
- 3 m leads come with fixed 1.5 m ground extensions
- Shrouded/stacking banana plugs
PicoBNC+ Premium Test Lead to 4mm, 5m
- Fully shielded for the complete length of the signal cable
- 5 m leads come with fixed 1.5m ground extensions
- Shrouded/stacking banana plugs
Large Dolphin/Gator Clip
- Fully insulated with a 4 mm socket in the handle
- Easy connection to Pico Premium test lead
- Wide 30 mm opening jaw
Small Crocodile / Gator Clip
- Fully insulated with 4mm socket in the handle
- Toothed grip offers good contact on fine wire
- Easy connection to Pico Premium Test Leads
Battery Clip
- Fits all our BNC to 4 mm Pico Premium Test Leads
- Plier type clips designed to grab and hold the vehicle battery terminals
Red/Black Pair of Insulation Piercing Clips
- Provides the exact pressure needed to pierce the insulation of a wide range of wires
- Rotating banana jacks prevent test lead twisting
- Keeps the oscilloscope in-circuit while the wire is pierced
TA008 Acupuncture Back Pinning Probe Set
- Back pinning probe set
- Fit onto 4mm banana plugs, fine tips slide easily past connector seals
- 7 complete acupuncture probes, 3 probe sizes, replacement screws & needles
Flexible Back Pinning Probe
- Designed for back-probing under the insulation
- Flexible mid-section improves access to difficult terminals
- Fits easily onto Pico Premium Test Leads
Multimeter Probe
- When a quick non-clip-on connection is required
- Pushes easily onto a Pico Premium Test Lead
- 4mm socket, length 115mm. Also available in black
Shrouded to Unshrouded Adaptor
- Adapts 4mm shrouded plug to unshrouded plug
- Allows test lead connection into any breakout box
- Quick push-on connection
PicoScope professional breakout lead set
- 14 sets with flat blade connectors in different sizes
- 4 sets with round pins in different sizes
- 1 set with square pins in one size
6-Way Universal Breakout Lead
- Connect PicoScope any vehicle - Micro(0.6 mm)
- Eliminates the need to own many specific breakout leads for engine diagnostics
- Available with 0.6, 1.5, 2.3 & 2.8mm male & female spade connectors
TA012 Two Pin Break Out Lead
- Enables voltage readings from numerous 2 pin sensors in the engine compartment
- Separate access to individual wires allows easy current measurement with clamps
- Simultaneously display both injector current and voltage on your PicoScope
PP619 CAN-Bus Test Box
- Instantly Check Power & Ground Circuits
- Identify Communication Link Protocols
- Connect to PicoScope
Foam Tray for CAN-Bus Test Box
- Protect your tester and its cable in this foam storage tray
TA014 FirstLook Engine Diagnostic Sensor
- Fast & accurate automotive diagnosis from tail pipe
- Diagnose burnt valves, bad injectors & other problems without major disassembly
- Includes vacuum line adaptor & connector cable
MEMS Accelerometer
- Used in conjuction with the NVH interface
- Detects motion across the X,Y and Z axes
Mounting magnet for accelerometer
- Mounting magnet for the TA143 Accelerometer.
Standard Pico Microphone
- The standard Pico microphone for use with Pico's NVH Interface
Sensor Extension Cable 3 m
- A black 3 m extension cable for Pico's NVH interface
TA197 10:1 Attenuator
- Perform quick and accurate ignition waveform analysis of many automotive systems
- Allows voltages of up to 400 V to be measured
- Increases the input impedance of the oscilloscope from 1 MΩ to 8 MΩ
USB Cable
- Connect PicoScope to PC
- Scope power and high signal rating
- Compatible with USB2 PCs
WPS500X
- Kit includes WPS500X Transducer, carry case & these accessories..
- Vacuum, exhaust, fuel & bleed hoses/adaptors, M10~14 short &/or deep reach adaptors.
- Use the kit to measure more, with greater ease and at a lower total cost.
WPS500X Maxi
- Kit includes WPS500X Transducer, carry case & these accessories..
- Vacuum, exhaust, fuel & bleed hoses/adaptors, M10~14 short &/or deep reach adaptors.
- Fuel hose pressure taps & additional adaptors
WPS600 Hydraulic Pressure Transducer
- Convenient analysis and diagnosis of pressurized systems
- Accurately measure up to 600 bar (8700psi)
- Two pressure ranges for increased versatility