Reset Selection
PicoScope 4225A 2 Channel Starter Kit
  • Lowest possible cost entry into your PicoScope ownership
  • Comes complete with a basic set of leads and clips
  • Accessories can be added at any time, to upgrade the kit and broaden its applications base.
PicoScope 4425A 4 Channel Starter Kit
  • Contains the same 4 channel Scope featured in the Standard and Advanced kits
  • Supplied with a set of leads and clips to perform the more common tasks
  • Purchase accessories to upgrade to a standard or advanced kit.
PicoScope 4225A 2 Channel Standard Kit
  • Comes complete with a variety of accessories
  • Test virtually all the components on modern vehicles
  • Ideal for occasional use or for those on a limited budget
PicoScope 4425A 4 Channel Standard Kit
  • Four input channels are a particular advantage when testing the likes of ABS systems
  • Fast enough to keep up with the emerging FlexRay standard
  • Supplied with a comprehensive array of connection and interfacing accessories
  • Smart connectors
PicoScope 4425A 4 Channel Advanced Kit
  • The Advanced Kit builds on the standard kit to include more accessories
  • Includes universal break out leads, fuse extensions, COP probes and extension leads
  • Oscilloscope buffer memory has 250 Meg samples
PicoScope 4425A 4 Channel Diesel Kit
  • Specifically designed around heavy duty diesel engines
  • Includes a 2000 Amp DC clamp
  • Fast sampling rate supports the capture and viewing of FlexRay and CAN bus signals
PicoScope 4425A 4 Channel Master Kit
  • The Master Kit has you covered with a raft of accessories
  • Includes universal break out leads, fuse extensions, COP probes and extension leads
  • Oscilloscope buffer memory has 250 Meg samples
WPS500X Automotive Pressure Transducer
  • Perform quick and accurate pressure analysis of many automotive systems.
  • Accurately measure up to 34.47 Bar (500 psi). Auto zeroing. Ultra fast 100μs response time.
  • Internal rechargeable LiPo battery.
  • Kit includes WPS500X Transducer, protective carry case & these Accessories...
  • Vacuum, exhaust, fuel & bleed hoses/adaptors, M10~14 short &/or deep reach adaptors.
  • Use the kit to measure more, with greater ease and at a lower total cost.
  • Kit includes WPS500X Transducer, Protective carry case & these Accessories...
  • Vacuum, exhaust, fuel & bleed hoses/adaptors, M10~14 short &/or deep reach adaptors.
  • Use the kit to measure more, with greater ease and at a lower total cost.
WPS600 Hydraulic Pressure Transducer
  • Convenient analysis and diagnosis of pressurized systems
  • Accurately measure up to 600 bar (8700psi)
  • Two pressure ranges for increased versatility
NVH Starter Diagnostic Kit
  • Identify unwanted vibration and noise sources in a vehicle.
  • Provides real-time diagnosis for the technician
  • Three axis starter kit in foam tray
NVH Standard Diagnostic Kit
  • Enables the identification of unwanted vibration and noise sources in a vehicle.
  • Providing real-time simultaneous diagnosis for the technician
  • Four axis kit in foam tray
Advanced NVH Diagnostic Kit
  • Four Noise, Vibration and Harshness modules to use with...
  • 4 channel PicoScopes for single or multi-axis analysis.
  • Kit includes 4 triple-axis accelerometers, 4 microphones and extension cables
Optical sensor kit
  • Providing a high-quality optical sensor and magnetic mount for use with our balancing software
  • Primarily used for balancing of propshafts
  • Also supports frequency measurement of other rotating items.
3-Axis NVH Interface
  • Add more inputs to your PicoDiagnostics NVH kit
  • Use with Picoscope TA143 MEMS Accelerometer or the TA144 Microphone
NVH Starter to Standard Kit Upgrade
  • Upgrade your starter kit
  • Add an additional sound input and an extra 3-axis accelerometer
  • Up to 400 MS/s real-time sample rate
  • 20 MHz bandwidth
  • Easy to use with any vehicle
TA014 FirstLook Engine Diagnostic Sensor
  • Fast & accurate automotive diagnosis from tail pipe
  • Diagnose burnt valves, bad injectors & other problems without major disassembly
  • Includes vacuum line adaptor & connector cable
PP619 CAN-Bus Test Box
  • Instantly Check Power & Ground Circuits
  • Identify Communication Link Protocols
  • Connect to PicoScope
  • Connect into any vehicle without specialised leads
  • Eliminates the need to own many specific breakout leads for engine diagnostics
  • Available with 0.6, 1.5, 2.3 & 2.8mm male & female spade connectors
TA012 Two Pin Break Out Lead
  • Enables voltage readings from numerous 2 pin sensors in the engine compartment
  • Separate access to individual wires allows easy current measurement with clamps
  • Simultaneously display both injector current and voltage on your PicoScope
  • ATC /ATO fuse extender keeps fuse in circuit while testing
  • Allows easy current (clamp) measurement.
  • Simply move fuse to extension, plug extension in where fuse was and clamp to measure
Mixmaster Secondary Ignition Pickups
  • A set of 4 secondary ignition, leads, each 40cm long
  • Combine with Mixmaster & 4-channel scope leads to display 12 channel parade
  • Get the most from your Mixmaster
  • Single extension lead
  • Clip Pico secondary ignition lead over extension to see HT waveform
  • Simply fit between coil pack & plugs
Coil-On-Plug (COP) Ignition Probe & Cable
  • Display scope patterns of the secondary, faster than scoping the primary
  • Suitable for use on most COP & conventional ignition systems
  • Find misfires fast
Secondary Ignition Pickup
  • View secondary ignition waveforms directly on-screen with an Automotive Oscilloscope
  • Shielded 1.8m lead. Clips over plug lead or COP extension
  • For use with conventional ignition systems and most HEI and DIS systems
TA167 - 200A/2000A AC/DC current clamp
  • Measure high compression diesel and petrol starter currents
  • 0 to 200/2000 Amps DC & AC pk (to 20kHz)
  • Easy push-button Zero Set
Mixmaster 12 Cylinder Auto Signal Mixer
  • View ignition parades of up to 12 cylinders
  • Display 2 engine banks of up to 6 cylinders each
  • Supplied with 4 secondary ignition leads, extra leads available
TA008 Acupuncture Back Pinning Probe Set
  • Back pinning probe set
  • Fit onto 4mm banana plugs, fine tips slide easily past connector seals
  • 7 complete acupuncture probes, 3 probe sizes, replacement screws & needles
  • When a quick non-clip-on connection is required
  • Pushes easily onto a Pico Premium Test Lead
  • 4mm socket, length 115mm. Also available in black
  • Designed for back-probing under the insulation
  • Flexible mid-section improves access to difficult terminals
  • Fits easily onto Pico Premium Test Leads
  • Fully insulated with a 4 mm socket in the handle
  • Easy connection to Pico Premium test lead
  • Wide 30 mm opening jaw
  • Fully insulated with 4mm socket in the handle
  • Toothed grip offers good contact on fine wire
  • Easy connection to Pico Premium Test Leads
  • Red single
  • Fits all our BNC to 4 mm Pico Premium Test Leads
  • Plier type clips designed to grab and hold the vehicle battery terminals
Red/Black Pair of Insulation Piercing Clips
  • Provides the exact pressure needed to pierce the insulation of a wide range of wires
  • Rotating banana jacks prevent test lead twisting
  • Keeps the oscilloscope in-circuit while the wire is pierced
  • Adapts 4mm shrouded plug to unshrouded plug
  • Allows test lead connection into any breakout box
  • Quick push-on connection
  • Set of four colours, removable and fixed ground
  • Leads match scope trace colours
  • 3m insulated BNC to stackable shrouded banana plugs
  • For working on larger vehicles
  • 5m long BNC to 4mm cable, with 2.5m fixed ground
  • Insulated BNC connector, shrouded 4mm plugs
  • Connect PicoScope to PC
  • Scope power and high signal rating
  • Compatible with USB2 PCs
Ultrasonic parking sensor detector
  • Prove the correct operation of each of the ultrasonic parking sensors
  • Directly showing the strength of the signal from a given sensor
  • 2m long lead
TA197 10:1 Attenuator
  • Perform quick and accurate ignition waveform analysis of many automotive systems
  • Allows voltages of up to 400 V to be measured
  • Increases the input impedance of the oscilloscope from 1 MΩ to 8 MΩ
Keyless entry carrier signal detector
  • Detect the presence of the keyless entry carrier frequency
  • In the range of 125-140 kHz
  • 3m long lead
MI168 S-Hook
  • Makes it easy to keep test leads tidy in the engine bay
  • Hang PicoScope up by its boot loop
  • 100 mm long, plastic coated with rubber caps
BNC to BNC Cable with Earth Clamp
  • For use with the Coil-On-Plug Ignition Probe
  • Length: 3 metres
8088 Multifunction Automotive Multimeter
  • mS Pulse, Frequency, Capacitance, Dwell & Temperature
  • Min & Max Record Functions
  • RPM (with Pickup) for 2 & 4 Stroke
*15% GST applicable for sales within NZ