PicoScope 4225A 2 Channel Standard Kit
|
 
 
 
PicoScope 4225A 2 Channel Standard Kit
  • Comes complete with a variety of accessories
  • Test virtually all the components on modern vehicles
  • Ideal for occasional use or for those on a limited budget

Includes: PicoScope Automotive Software

The 2 Channel Standard Kit comes complete with a variety of accessories including leads, ignition pickups, probes, clips and current clamps – allowing you to test virtually all the components on modern vehicles.

Our 2 channel standard kit is ideal for occasional use or for those on a limited budget. The four channel kits allow users to diagnose more complex problems and save time by testing more signals simultaneously.

Which Diagnostics Kit is Right for Me?
Compare Kits


$ 3855.00*

    Carry Case
    • For measuring currents between 10 mA and 60 A
    • Display current waveforms for fuel injectors and fuel pumps.
    • Improved performance and diagnostic accuracy
    PicoBNC+ 60A AC/DC current clamp
    • Allows you to measure up to 2000 amps without cutting, or disconnecting or stripping wires
    • No batteries required
    • Ranging is carried out automatically with no user switching required
    PicoBNC+ 2000 A AC/DC current clamp
    • Fully shielded for the complete length of the signal cable
    • 3 m leads come with fixed 1.5 m ground extensions
    • Shrouded/stacking banana plugs
    2x PicoBNC+ Premium Test Lead to 4mm, 3m
    • View secondary ignition waveforms directly on-screen with an Automotive Oscilloscope
    • Shielded 1.8m lead. Clips over plug lead or COP extension
    • This lead is fitted with a PicoBNC+ interface
    2x PicoBNC+ secondary ignition pickup
    • ATC /ATO fuse extender keeps fuse in circuit while testing
    • Allows easy current (clamp) measurement.
    • Simply move fuse to extension, plug extension in where fuse was and clamp to measure
    Fuse Extension Lead - Std ATC/ATO
    • Mini ATC fuse extenders keep fuse in circuit while testing.
    • Allows easy (clamp) current measurement.
    • Simply move fuse to extension, plug extension in where fuse was and clamp to measure.
    Fuse Extension Lead - Mini-ATC
    • Displays scope patterns of the secondary, faster than scoping the primary
    • Flexible design allows for easier access to hard-to-reach components
    • No batteries required
    PicoBNC+ COP and signal probe
    • These probes have a fixed x10 attenuation and are intended for high-speed signals
    • Automatically recognised by PicoScope software when connected to the scope.
    BNC+ 10:1 scope probe & adaptor
    • Single extension lead
    • Clip Pico secondary ignition lead over extension to see HT waveform
    • Simply fit between coil pack & plugs
    Coil-on-Plug Extension Lead - Single
    • Back pinning probe set
    • Fit onto 4mm banana plugs, fine tips slide easily past connector seals
    • 7 complete acupuncture probes, 3 probe sizes, replacement screws & needles
    TA008 Acupuncture Back Pinning Probe Set
    • Designed for back-probing under the insulation
    • Flexible mid-section improves access to difficult terminals
    • Fits easily onto Pico Premium Test Leads
    Flexible Back Pinning Probe (2x Red, 2x Black)
    • When a quick non-clip-on connection is required
    • Pushes easily onto a Pico Premium Test Lead
    • 4mm socket, length 115mm. Also available in black
    Multimeter Probe (1x Red, 1x Black)
    • Fully insulated with 4mm socket in the handle
    • Toothed grip offers good contact on fine wire
    • Easy connection to Pico Premium Test Leads
    Small Crocodile / Gator Clip (1x Red, 1x Black)
    • Adapts 4mm shrouded plug to unshrouded plug
    • Allows test lead connection into any breakout box
    • Quick push-on connection
    2x Shrouded to Unshrouded Adaptor
    • Fits all our BNC to 4 mm Pico Premium Test Leads
    • Plier type clips designed to grab and hold the vehicle battery terminals
    Battery Clip (1x Red, 1x Black)
    • Makes it easy to keep test leads tidy in the engine bay
    • Hang PicoScope up by its boot loop
    • 100 mm long, plastic coated with rubber caps
    MI168 S-Hook
    • Connect PicoScope to PC
    • Scope power and high signal rating
    • Compatible with USB2 PCs
    USB Cable - Vsn 3.1 Gen 1, 1.8m